A. A switch.
B. A router.
C. A network adapter card.
D. A hub.
E. A repeater.
您可能感興趣的試卷
你可能感興趣的試題
The TestKing network Topology is displayed in the exhibit below
A switch has been configured for three different VLANs: VLAN 2, VLAN 3, andVLAN 4. For the purposes of communication between VLANs a router is to beadded. Host from one VLAN should be able to reach the hosts in the other VLANs.
Based on this requirement, what type of connection is acceptable between the routerand switch?（）
A. 10 Mbps Ethernet
B. 56 kbps serial
C. 100 Mbps Ethernet
D. 1,544 Mbps serial
E. 1000 Mbps Ethernet
An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network.
What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）
A. The switch that will share its VLAN configuration must be in VTP server mode.
B. The switches must be in the same VTP domain.
C. The switch that will share the VLAN information must be configured as the root bridge.
D. The switches must be connected over VLAN trunks.
E. The switches must be configured to use the same STP version.
F. The switches must have VTP pruning activated.
A. By default, all defined VLANs are allowed on the trunk.
B. Each single VLAN, or VLAN range, must be specified with the switchport mode command.
C. Each single VLAN, or VLAN range, must be specified with the vtp domain command.
D. Each single VLAN, or VLAN range, must be specified with the vlan database command.
A. They increase the size of collision domains.
B. They allow logical grouping of users by function.
C. They can enhance network security,
D. The increase the size of broadcast domains while decreasing the number of the broadcast domains.
E. The increase the number of broadcast domains while decreasing the size of the broadcast domains.
F. They simplify switch administration.
A. Switch(vlan)# mode trunk
B. Switch(config)# switchport access mode trunk
C. Switch(config-if)# switchport mode trunk
D. Switch(config-if)# switchport trunk encapsulation dot1q
E. Switch(config)# switchport access mode 1
F. Switch(vlan)# trunk encapsulation dot1q
最新試題
The network 172.12.0.0 needs to be divided into subnets where each subnet has the capacity of 458 IP addresses.What would be the correct subnet mask to accomplish this division keeping the number of subnets at the maximum? （）
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）
The following access list was applied outbound on he E0 interface connected to the 192.168.1.8/29 LAN:access-list 123 deny tcp 192.168.1.8 0.0.0.7 eq 20 anyaccess-list 123 deny tcp 192.168.1.9 0.0.0.7 eq 21 anyWhat effect will this access list have?（）
What does a configuration Register Setting of 0x2105 indicate to the Router? （）
A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? （）
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?（）
What feature of a networks switch allows an administrative to create separate broadcast domains?（）
A technician at TestKing needs to update the network documentation. One of the tasks includes documenting the name of the IOS image file of each router in the network.Which commands could be used to find this information?（）
What is a global command?（）